Tectonic Elements TEBM35C10-4 Miniature BMR® Driver

IMG_3960 IMG_3962I was recently browsing the Parts-Express website and came upon some products from Tectonic Elements that I thought were interesting: the BMR series speakers.  BMR stands for Balanced Mode Radiator.  Some words from their website:

Tectonic Elements has developed a methodology for controlling modal bending wave activity enabling pistonic action and surface excitation to be combined in a single transducer or driver. This results in a small form-factor speaker drive that delivers uncanny sound quality due to its wide dispersion of sound, and full range response. Listeners have described itʼs audio fidelity as ʻlifelikeʼ and ʻunencumbered by the attributes of speaker mechanicsʼ. Tectonic Elements’ family of products utilising this patented technology is called BMR® and are set to transform listening pleasure from small format, low-cost loudspeakers.

 

Paint me intrigued!  A few google search results later and I had found some really positive words for their 3 inch full range driver found here.

A few minutes later I found that Tectonic Elements was releasing a 2 inch driver: the TEBM35C10-4.  The data sheet looked quite impressive.  Here’s a little blurb from their site:

The TEBM35C10-4 BMR® is an audio drive unit with an extended frequency response and extremely wide directivity. It combines the benefits of Tectonic Elements bending-wave technology and pistonic modes of operation. The small form-factor is ideally suited for compact products that require a full-range drive unit, room filling sound and a high performance acoustic solution.

I couldn’t find these available to purchase so I contacted the company.  What a great bunch… they were happy to send me a couple samples of their TEBM35C10-4 driver.  So, here we are… let’s get to testing!

Size wise, these are small.  Here’s a few quick dimensions:

  • Outer Diameter = 52mm (54mm counting the mounting tabs)
  • Mounting Depth = 23mm (surface mounted), 25.1 (flush mounted)

 

Impedance and Thiele-Small Testing:

Results were obtained via Dayton’s DATS v2 using the added mass method.

  • Effective Diameter = 37.08 [mm]
  • Re = 4.181 [Ohms]
  • Fs = 146 [Hz]
  • Zm = 18.69 [Ohms]
  • BL = 2.134 [N/A]
  • Qms = 3.848
  • Qes = 1.109
  • Qts = 0.8608
  • Vas = 0.148 [liters]
  • Le(10k) = 0.07819 [mH]
  • dBSPL = 78.08 [1W/1m]
  • Ms = 1.316 [grams]
  • Cms = 0.903 [mm/N]

tectonics elements tebm35c10-4 impedance

Frequency Response:

The following response measurements were taken at 2.83v at 1 meter.  Nearfield response was merged with far-field at approximately 3khz.

The measurements were performed at 0, 15, 30, 45, and 60 degrees.

  • 0 = Black
  • 15 = Blue
  • 30 = Purple
  • 45 = Red
  • 60 = Green
FR without legend

2.83v/1m. 0, 15, 30, 45, 60 degrees.

Harmonic Distortion:

Distortion testing was done in the nearfield to emulate the following farfield responses:

90dB @ 1m:

HD @ 90dB96dB @ 1m:

HD @ 96dB

Here’s the same result above but with a pointer for the 3% THD mark:

hd @ 96dB with 3% pointer

 

Conclusion:

This driver has an incredible bandwidth for it’s size.  This driver literally fits in my palm yet should have no problems playing from 300-400hz (with a proper high-pass; listener dependent) all the way up to 20khz without issue.  Cone breakup is practically non-existant with only a hint of breakup at 18khz.  THD is very, very low given it’s size.  At 96dB output the 3% THD mark is about 300hz; Above 500hz the THD is <1%.  Use this with a high-pass filter and most shouldn’t have an issue crossing down to 400hz.  At 30 degrees off axis the response is down 3dB and at 60deg off axis the response is 7dB down at 10khz.  Those numbers are on par with some of my favorite 1 inch tweeters.  I’m very impressed.  Of course, all this comes at a cost and the cost here is: sensitivity.  On average this driver runs about 77dB at 2.83v/1m.  Bummer.  Compression testing would benefit me here but since I have nothing to A/B it against, I’m gonna let it stand.  Of course, a high-pass filter also remedies compression to a good degree and since I don’t expect someone listening to this driver at high output near Fs, I suspect compression issues will be fairly inconsequential.

Naturally people will compare this to the AuraSound 2″ driver (aka: the “whisper”).  While the whisper has approximately 4dB higher sensitivity on average, this driver has a lower Fs, low THD, and an excellent polar response.  I don’t believe the whisper can cover the same bandwidth as well as this particular Tectonic Elements driver can.

Price wise, we will have to wait and see.  Since this driver hasn’t been released yet there’s no definite way to know what the retail price will be.  However, based on their other products sold in the US by Parts-Express, I’d expect pricing to be somewhere in the $15-20 range.  If that holds true,

Array anyone?….I’d really be interested to see how these perform in an array.  Hopefully I’ll get the time to perform that kind of testing and I will definitely post the results if/when I do.

PS:  If you would like to help me keep up funds for testing, there’s a little ‘contribute’ button that goes through Paypal all the way at the bottom of every page.  Any little bit helps.

One thought on “Tectonic Elements TEBM35C10-4 Miniature BMR® Driver

Leave a Reply

Your email address will not be published. Required fields are marked *